Danish loudspeakers Danish designed loudspeakers with the latest technology ensure the Studio delivers on its promises: symmetric magnetic motor, solid aluminium basket, extensive venting, to name a few

Controlled directivity By integrating the cabinet design, cross over and drivers, the Studio has a controlled directivity of sound, meaning the Studio is less critical to the listening room acoustics

Hand build in Denmark Build by hand in the for Denmark typical small scale production adds a personal touch to each loudspeaker.

FAQ More questions? Check out the FAQ page for information on amplifiers, sound quality and much more

Select your veneer Vist the Factory and be there during the build. You will be able to select the veneer you like best

Finely tuned cross over the elaborate 24 dB/oct Linkwitz- Riley cross over gives more upper mid range energy for a more open sound and improves the tweeter high power performance.

Clean upper bass The small size of the Studio cabinet naturally prevents internal standing waves for a clean upper bass

Danish Design Carefully considered curves are the heart of each unique Davone design. The perfect rhythm and balance of the design visualize music.

the Magnetic Motor

All loudspeakers may look alike for the untrained eye. But to reduce cost, usually chassis are made from plastic, the magnet and voice coil are too small and the magnetic motor will be from simple, unoptimized geometry, to name a few. In contrast, take a look at the woofer that is used in the Studio that has been optimized for quality instead of cost:

1. The magnetic structure is optimised using advanced Finite Element Analysis software. The result is a magnetic field with a better than 95% symmetry within the voice coil travel range of +/-12 mm. Compared to traditional designs, the harmonic distortion is greatly reduced, especially at higher loudness levels


2. Large magnet structure with 39 mm heavy-duty fiber glass vented voice coil for better control, power handling, dynamic performance and low-level details


3. Copper cap on center pole to reduce voice coil inductance and to minimize variations in voice coil inductance as a function of voice coil position


4. Cone made of a paper/glass fiber mix with improved stability


5. Rigid die cast alu chassis with extensive venting for lower air flow speed reducing audible distortion

• Frequency response

  45-22.000Hz

  
  

  Impedance

  4 ohm, 3.7 ohm minimum at 350Hz

  
  

  Sensitivity

  88 dB/2,83V/m

  
  

  Recommended Amplifer power

  100-200 Watt

  
  

  Mid woofer

  180mm, low distortion driver with a special fibre blend cone with optimal balance of stiffness, damping and density. Symmetric motor structure for optimal drive force symmetry. Designed in Denmark

  
  

  System

  Bass reflex

• Tweeter

  1", Anodised aluminium dome, flow optimized vented pole piece with non-reflective chamber, saturation controlled motor system. Designed in Denmark

  
  

  Cross over

  2.4kHz, 24dB/Oct Linkwitz Riley

  
  

  Cabinet Construction

  6 layer beech wood form pressed veneer

  
  

  Weight

  9.3 kg / piece

  
  

  Height / Width / Depth

  36 / 24 / 30 cm

  
  

  Current version

  HR

  
  

  Designer

  Paul Schenkel

Black fine weave polyester, other colours on request

Kvadrat Metric #023, Anthracite

Kvadrat Metric #025, Blue-Grey

Kvadrat Metric #008, Warm Brown

Kvadrat Metric #009, Lighter Warm Brown

Kvadrat Metric #016, Dark Caramel

Kvadrat Metric #017, Caramel

Kvadrat Metric #002, Light Grey

Quarter cut Walnut

Black ash

Desktop Stand Stainless (optional)



3(H) / 20(W) / 25(D) cm


Floor Stand (optional)



64(H) / 28(W) / 31(D) cm


Floor Stand Finish



Sand grain texture powdercoat, black